Libnor | Catalogs |

Document Number: NL EN 12199 : 2017

This European Standard specifies the characteristics of homogeneous and heterogeneous smooth (including grained or embossed) rubber floor coverings, supplied in either tile or roll form. This European Standard includes a classification system based on intensity of use, which shows where these resilient floor coverings should give satisfactory service (see EN 685). It also specifies requirements for marking

Resilient Floor Coverings - Specifications for Homogeneous and

Sector: Domestic and Commercial Equipment. Entertainment.

Document Number: NL ISO 10130 : 2017

This European Standard specifies the characteristics of homogeneous and heterogeneous relief or studded rubber floor coverings, supplied in either tile or roll form. This European Standard includes a classification system based on intensity of use, which shows where these resilient floor coverings should give satisfactory service (see EN 685). It also specifies requirements for marking.

Cosmetics — Analytical methods — Nitrosamines: Detection and determination of N-nitrosodiethanolamine (NDELA) in cosmetics by HPLC, postcolumn photolysis and derivatization

Document Number: NL ISO 12787 : 2017

This International Standard describes a method for the detection and quantification of N-nitrosodiethanolamine (NDELA) in cosmetics and raw materials used in cosmetics by high performance liquid chromatography (HPLC) coupled with post-column photolysis and derivatization. This method is not applicable to the detection and/or quantification of nitrosamines other than NDELA, nor to the detection and/or quantification of NDELA in products other than cosmetics or raw materials used in cosmetics. If a product has the possibility of either NDELA contamination from the ingredients or NDELA formation by the composition of ingredients, the method will be applied for the testing of cosmetic products and is an alternative to ISO 15819. This method is not applicable to matrices containing oxidation dyes.

Cosmetics — Analytical methods — Validation criteria for analytical results using chromatographic techniques

Document Number: NL ISO TR 14735 : 2017

This International Standard defines validation criteria with which analytical results obtained from the analysis of cosmetic products should comply in order to give confidence in performance, reliability and quality of the final result. It sets out an analytical approach that can be used by a single laboratory to carry out chromatographic analyses on a given sample, or samples.

Cosmetics — Analytical methods — Nitrosamines: Technical guidance document for minimizing and determining N-nitrosamines in cosmetics

Document Number: NL ISO 15819 : 2017

This Technical Report aims to contribute to providing general advice on strategies that can be adopted to minimize the likelihood of N-nitrosamine formation in cosmetic products and provide a description of the analytical methodologies available for the reliable determination of N-nitrosamines in cosmetic products. It also seeks to provide some insight into the relevance and limitations of each of the methods described and finally provide an analytical approach for the analysis of N-nitrosamines in cosmetic products and raw materials. This Technical Report covers the reduction or elimination of adventitious nitrite sources, reduction or elimination of secondary amino sources, incorporation of inhibitors to N-nitrosamine formation and analytical methodologies for total N-nitroso compounds and specific methods for N-nitrosodiethanolamine (NDELA).

Cosmetics — Analytical methods — Nitrosamines: Detection and determination of N-nitrosodiethanolamine (NDELA) in cosmetics by HPLC-MS-MS

Document Number: NL ISO 21148 : 2017

This International Standard describes a method for the detection and quantification of N nitrosodiethanolamine (NDELA) in cosmetics and raw materials used in cosmetics. This method is not applicable to the detection and/or quantification of nitrosamines other than NDELA nor to the detection and/or quantification of NDELA in products other than cosmetics or raw materials used in cosmetics. If a product has a possibility of either NDELA contamination from ingredients or NDELA formation by the composition of ingredients, the method is intended to be applied for quantitative determination of NDELA. Accordingly, the method does not apply to routine testing of cosmetic products. Because of the large variety of cosmetic products within this field of application, this method might need to be adapted for certain matrices (refer to ISO 12787). Therefore, International Standards dedicated to alternative methods for testing nitrosamines in cosmetic products are being developed separately. Other methods can be employed provided that they are verified as to their detection of NDELA and validated in terms of recovery and quantification of the analyte.

Cosmetics — Microbiology — General instructions for microbiological examination

Document Number: NL ISO 24442 : 2017

This International Standard gives general instructions for carrying out microbiological examinations of cosmetic products, in order to ensure their quality and safety, in accordance with an appropriate risk analysis (e.g. low water activity, hydro-alcoholic, extreme pH values). Because of the large variety of products and potential uses within this field of application, these instructions might not be appropriate for some products in every detail (e.g. certain water-immiscible products).

Cosmetics — Sun protection test methods — In vivo determination of sunscreen UVA protection

Document Number: NL ISO 24444 : 2017

This International Standard specifies an in vivo method for assessment of the UVA protection factor (UVAPF) of topical sunscreen products. This International Standard is applicable to cosmetics, drugs and other products intended to be topically applied to human skin, including any component able to absorb, reflect or scatter UV rays. It provides a basis for the evaluation of sunscreen products for the protection of human skin against UVA radiation from solar or other light sources.

Cosmetics — Sun protection test methods — In vivo determination of the sun protection factor (SPF(

Document Number: NL ISO TR 26369 : 2017

This International Standard specifies a method for the in vivo determination of the sun protection factor (SPF) of sunscreen products. This International standard is applicable to products that contain any component able to absorb, reflect or scatter ultraviolet (UV) rays and which are intended to be placed in contact with human skin. It provides a basis for the evaluation of sunscreen products for the protection of human skin against erythema induced by solar ultraviolet rays.

Cosmetics — Sun protection test methods — Review and evaluation of methods to assess the photoprotection of sun protection products

Document Number: NL ISO 24443 : 2017

This Technical Report reviews and evaluates the methods which are currently used to assess, for regulatory or self-regulatory purposes, the photoprotection of sun protection products applied on the human body. It is applicable to SPF and UVA protection, and both in vivo and in vitro methods. This Technical Report does not include the aspects of labelling in a wide sense.

Cosmetics - Determination of sunscreen UVA photoprotection in vitro

Document Number: NL ISO TR 17276 : 2017

This International Standard specifies an in vitro procedure to characterize the UVA protection of sunscreen products. Specifications are given to enable determination of the spectral absorbance characteristics of UVA protection in a reproducible manner. In order to determine relevant UVA protection parameters, the method has been created to provide a UV spectral absorbance curve from which a number of calculations and evaluations can be undertaken. Results from this measurement procedure can be used for other computations, as required by local regulatory authorities. These include calculation of the Ultraviolet-A protection factor (UVAPF) [correlating with in vivo UVAPF from the persistent pigment darkening (PPD) testing procedure], critical wavelength and UVA absorbance proportionality. These computations are optional and relate to local sunscreen product labelling requirements. This method relies on the use of in vivo SPF results for scaling the UV absorbance curve. This International Standard is not applicable to powder products such as pressed powder and loose powder products.

Cosmetics — Analytical approach for screening and quantification methods for heavy metals in cosmetics

Document Number: NL EN 14901 : 2017

This Technical Report introduces most common and typical analytical approaches for screening and quantification of heavy metals of general interest at both raw material and finished product level. This Technical Report covers techniques from traditional colourimetric reaction, which can be executed without expensive instrument to the high-end one, like that of inductively coupled plasma-mass spectrometry (ICP-MS), which allows detection of elements at μg/kg level. Thus, this Technical Report covers the advantages and disadvantages of each analytical technique so that a suitable approach can be chosen. The intent of this Technical Report is not to set or suggest acceptable concentration limits of heavy metals in both raw materials and finished products which have to be determined by each regulatory authority. NOTE 1 The term “heavy metals” is widely used without single definition. NOTE 2 Elements can be specified as heavy metals by one legislation, while not by others.

Ductile iron pipes, fittings and accessories - Epoxy coating (heavy duty) of ductile iron fittings and accessories - Requirements and test methods

Document Number: NL EN 15655 : 2017

This European Standard defines the requirements and test methods for factory applied epoxy coatings (fusion bonded powder or liquid two-pack) used for the corrosion protection of ductile iron fittings and accessories conforming to EN 545, EN 598, EN 969, EN 12842, EN 14525, for: - conveying water (e.g. potable water) at operating temperature up to 50 °C excluding frost; or - conveying waste water at operating temperature up to 45 °C excluding frost; or - conveying gas at operating temperature up to 50 °C; - suitable for external environments, i.e. soils, waters and atmospheres of all common corrosion loads, characterized in EN 545:2010, D.2.3.

Ductile iron pipes, fittings and accessories - Internal polyurethane lining for pipes and fittings - Requirements and test methods

Document Number: NL EN 14525 : 2017

This European Standard defines the requirements and test methods applicable to factory applied internal polyurethane high duty corrosion protection of buried ductile iron pipes and fittings conforming to EN 545, EN 598 and EN 969 for use at permanent operating temperatures up to 45 °C

Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, Steel, PVC-U PE, Fibre-cement

Sector: Fluid systems and components for general use

Document Number: NL EN 15189 : 2017

This document specifies the requirements and associated test methods applicable to wide tolerance ductile iron couplings and wide tolerance flange adaptors intended for use with pipe components made from a number of pipe materials (ductile iron, grey iron, PE, PVC-U, steel, fibre-cement), for providing a leak tight seal over a wide range of pipe external diameters : - to convey water (e.g. potable water) ; - with or without pressure ; - to be installed below or above ground, inside or outside buildings. This standard is not intended to cover sewerage or gas applications, where other requirements may be necessary. This standard specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron products. This standard covers ductile iron products cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints, in a size range extending from DN 40 to DN 600, for an allowable operating pressure (PFA) up to 16 bar, for fluid temperatures between 0 °C and 25 °C excluding frost. For higher temperatures, up to 50 °C, additional type testing should be carried out. It also gives performance requirements and associated test methods for restrained and non-restrained flexible joints. Joint design and gasket shapes are outside the scope of this standard. NOTE 1 PFA may be limited depending on pipe materials effectively connected. NOTE 2 In this standard, all pressures are relative gauge pressures, expressed in bars (100 kPa = 1 bar). NOTE 3 EN 545 gives the specifications for the ductile iron fittings to be used with ductile iron pipes. NOTE 4 EN 12842 gives the specifications for the ductile iron fittings to be used with PVC-U and PE pipes.

Medical laboratories -- Requirements for quality and competence

Sector: FLUID SYSTEMS AND COMPONENTS FOR GENERAL USE

Document Number: NL EN 15542 : 2017

This European standard defines the requirements and test methods applicable to factory applied external polyurethane based coatings for heavy duty (Annex D.3 of EN 545:2002) corrosion protection of buried ductile iron pipes conforming to EN 545, EN 598 and EN 969 for use at operating temperatures up to 50 °C. This standard does not cover ductile iron pipes protected with zinc with a finishing layer of polyurethane. This standard does not cover special activities on site such as tapping, clamping, etc., which could affect the corrosion protection properties of the polyurethane coating. These operations should be covered in the laying instructions supplied by manufacturers of clamps, house connection saddles, etc. and any relevant user procedures.

Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, Steel, PVC-U PE, Fibre-cement

Document Number: NL EN 1074 1 : 2017

This European Standard defines the requirements and test methods applicable to factory applied cement mortar coatings for the external corrosion protection of ductile iron pipes conforming to EN 545, EN 598 and EN 969 for use at operating temperatures up to 50 °C, and for soil conditions according to Annex D.3 of EN 545:2006. Special activities on site such as joint protection, tapping, clamping, etc. could affect the corrosion protection properties of the cement mortar coating. These operations should be covered in the laying instructions supplied by the manufacturers of pipes, clamps, house connection saddles, etc and any relevant users' procedures. Such instructions are not part of this European Standard.

Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 1: General requirements

Document Number: NL EN 1074 2 : 2017

This European Standard defines the minimum fitness for purpose requirements for valves to be used in, or connected to, water supply pipe systems above or below ground (see prEN 805, including the meter valves), and also suitable for pipe systems carrying raw or treated water (e.g. for irrigation, for fire fighting).

Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 2: Isolating valves

Document Number: NL EN 1074 3 : 2017

This standard defines the minimum fitness for purpose requirements for valves to be used in, or connected to, water supply pipe systems above or below ground (see prEN 805, including meter valves), and also suitable for pipe systems carrying raw or treated water (e.g for irrigation, for fire fighting).

Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 3: Check valves

Document Number: NL EN 1074 4 : 2017

This European Standard defines the minimum fitness for purpose requirements for check valves to be used in, or connected to, water supply pipe systems, above orbelow ground (see prEN 805:1996), carrying water intended for human consumption.This standard specifies the design requirements, the performance requirements and the conformity assessment method for check valves, whatever their type and materials. This standard applies in priority to any product or test standard: the requirements from other standards apply only when this standard refers to them.

Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 4: Air valves

Document Number: NL EN 1074 5 : 2017

This European Standard specifies the minimum fitness for purpose requirements for valves to be used in, or connected to, water supply pipe systems above or below ground (see EN 805), carrying water intended for human consumption. This standard specifies the design requirements, the performance requirements, and the conformity assessment method for valves, whatever their type and materials. This standard applies in priority to any other product or test standard : the requirements from other standards apply only when this standard refers to them. This standard deals with the requirements applicable to air valves with DN up to DN 300 and PFA 6 to PFA 25.

Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5: Control valves

Document Number: NL EN 1074 6 : 2017

This part of the standard determines the special requirements and tests to be applied to control valves for a range PN 6 to PN 25, the nominal dimensions of which are as defined in Part 1. The Type tests shall be carried out on valves of DN <= 500, by agreement between the supplier and purchaser, for higher DNs. This Part 5 does not deal with the performance of control valve accessories whether or not these form an integral part of the valves.

Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 6: Hydrants

Document Number: NL ISO 3549 : 2017

This European Standard defines the minimum fitness for purpose requirements for hydrants to be used in, or connected to, water supply pipe systems, above or below ground (see EN 805), carrying water intended for human consumption. This European Standard specifies the design requirements, the performance requirements, and the conformity assessment method for hydrants, whatever their type, materials and functions. Where hydrants can be used for fire fighting, irrigation or other function, additional requirements can be given in other standards. This part of EN 1074 deals with the requirements applicable to both underground and pillar hydrants, in sizes DN 65 to DN 150, and PFA up to 16 bar. This part of EN 1074 does not give requirements for the outlets or their interface with the hydrants, since they are subject to national standards.

Zinc dust Pigments for paints - Specifications and Test Methods

Document Number: NL ISO 1249 Cor : 2017

This International Standard specifies the requirements and corresponding test methods for zinc dust pigments suitable for use in protective coatings.

Zinc Chromate Pigments - Basic Zinc Potassium Chromate Pigments and Zinc Tetrahydroxychromate Pigments

Document Number: NL ISO 6745 : 2017

This International Standard specifies the requirements and corresponding test methods for zinc chromate pigments suitable for use in paints and/or corrosion-inhibiting coatings.

Zinc Phosphate Pigments for paints - Specifications and

Document Number: NL EN 688 : 2017

This International Standard specifies the requirements and the corresponding methods of test for zinc Phosphate Pigments suitable for use in corrosion-inhibiting paints.

Resilient Floor Coverings - Specification for Corklinoleum

Sector: Domestic and Commercial Equipment. Entertainment.

Document Number: NL EN 12455 : 2017

This European Standard specifies the characteristics of corklinoleum, supplied in roll form. To encourage the consumer to make an informed choice, the standard includes a classification system based on intensity of use, which shows where resilient floor coverings should give satisfactory service (see EN 685). It also includes requirements for marking. The term 'linoleum' is frequently incorrectly applied to a range of floor coverings, often to those based on polyvinyl chloride or rubber. Such materials are excluded from this standard.

Resilient Floor Coverings - Specification for Corkment Underlay

Sector: Domestic and Commercial Equipment. Entertainment.

Document Number: NL EN 652 : 2017

This European Standard specifies the requirements of corkment underlay with linoleum cement as binder, supplied in sheet form. Corkment underlay is used in combination with floor coverings to improve impact sound reduction. The performance therefore depends on the combination of corkment and the type of floor covering used and also the installation of both. To ensure correct use of corkment underlay the instructions of the manufacturer should be followed.

Resilient floor coverings - Polyvinyl Chloride Floor Coverings with Cork-Based Backing - Specification

Sector: Domestic and Commercial Equipment. Entertainment.

Document Number: NL EN 655 : 2017

This European Standard specifies the characteristics of floor coverings based on polyvinyl chloride and modifications thereof with a cork-based backing, supplied in either tile or roll form. To encourage the consumer to make an informed choice, the standard includes a classification system (see EN 685) based on intensity of use, which shows where these floor coverings should give satisfactory service. It also specifies requirements for marking.

Resilient floor coverings - Tiles of agglomerated composition cork with polyvinyl chloride wear layer - Specification

Sector: Domestic and Commercial Equipment. Entertainment.

Document Number: NL EN 686 : 2017

This European Standard specifies the characteristics of agglomerated cork with a wear layer based on polyvinyl chloride and modifications thereof. To encourage the consumer to make an informed choice, the European Standard includes a classification system (see EN 685) based on intensity of use, which shows where these floor coverings should give satisfactory service. It also specifies requirements for marking.

Resilient Floor Coverings - Specification for Plain and Decorative Linoleum on a Foam Backing

Sector: Domestic and commercial equipment. Entertainment.

Document Number: NL EN 687 : 2017

This document specifies the characteristics of plain and decorated linoleum on a foam backing as a compound floor covering, supplied in roll form. To encourage the consumer to make an informed choice, this document includes a classification system based on the intensity of use, which shows where resilient floor coverings provide satisfactory service. The term 'linoleum' is frequently incorrectly applied to a range of floor coverings, often to those based on polyvinyl chloride or rubber. Such materials are not included in this document.

Resilient Floor Coverings - Specification for Plain and Decorative Linoleum on a Corkment Backing

Sector: Domestic and commercial equipment. Entertainment.

Document Number: NL 658 : 2017

This European Standard specifies the characteristics of plain and decorative linoleum on a corkment backing as a compound floor covering, supplied in roll form. To encourage the consumer to make an informed choice, the standard includes a classification system based on intensity of use, which shows where resilient floor coverings should give satisfactory service (see EN 685). It also includes requirements for marking. The term "linoleum" is frequently incorrectly applied to a range of floor coverings, often to those based on polyvinyl chloride or rubber. Such materials are not included in this European Standard

General standard for the labelling of and claims for prepackaged foods for special dietary uses

Document Number: NL 206 : 2017

Price: 15000.0000

تنطبق هذه المواصفة القياسية على لصاقات جميع الأغذية المعباة مسبقا، المعدة لاستعمالات تغذوية خاصة، المعرف عنها في البند الرابع والمعروضة للمستهلك المباشر أو للتموين الجماعي، كما على الادعاءات المرتبطة بها وبعض الجوانب المتصلة بعرضها.

Labelling of Prepackaged Foods

Document Number: NL 660 : 2017

تهدف هذه المواصفة القياسية الى تحديد الشروط والمتطلبات الواجب توافرها في بطاقات المعلومات البيانية او لصاقات المعلومات البيانية العائدة للمواد الغذائية المعبأة أو الموضبة مسبقاً إن كانت معروضة بشكلها هذا مباشرة على المستهلك أو معدة للاستهلاك الجماعي.ً وهي تتطرق أيضا الى بعض النواحي المتعلقة بطريقة تسويق هذه المواد.

General Guidelines on Claims

Document Number: NL 661 : 2017

Price: 15000.0000

تهدف هذه المواصفة القياسة إلى وضع التوجيهٌات والتعليمات العامة لاستعمال البيانات الإدعائية الخاصة بالمواد الغذائية، ان كانت خاضعة أو غير خاضعة لمواصفات قياسية لبنانية فردية.

Guidelines for Use of Nutrition and Health Claims

Document Number: NL 719 : 2017

تطبق التوج هٌات الواردة ف هذه المواصفة الق اٌس ةٌ، على وجهة استعمال الب اٌنمات الإدعائ مٌة التغذو مٌة و الص ا ح اٌة ضمن لصاقات الأغذ ةٌ لكافة المنتجات و عند اللازوم من قبل ال ا سلطات المعن اٌة لجهة طمرق تسو قٌ و عرض المنتج. كممما تط ا بممق علممى كافممة المنتجممات التمم تحمموي ب اٌنممات إدعائ مٌمة تغذو مٌمة و صمم ا ح اٌة، مممن دون الإخمملال بالاشمتراطات الخاصمة المواردة فم إطمار المواصمفات والتوج هٌمات المتعلقمة بأغذ مٌمة الحم مٌمة والأغذ مٌمة المعدة لأغراض طب ةٌ خاصة. تهمدف همذه المواصمفة الق اٌسم ةٌ إلمى اسمتكمال "التوج هٌمات العاممة لاسمتعمال الب اٌنمات الادعائ مٌمة"، ولا تحل بدل أي من التحظ رٌات الواردة ف هٌا. لا جٌوز استخدام ب اٌنات إدعائ ةٌ تغذو ةٌ و صح اٌة لأغذ ةٌ الأطفال و ال ا ر ا ضمع ا ا لا فم حمال ن ا صمت علمى ذلك احدى ال ا تشر عٌات الوطن اٌة أو المواصفات الالبنان اٌة.

General guidelines on nutrition labelling

Document Number: NL ISO 4618 : 2017

تهدؾ هذه المواصفة الق اٌس ةٌ إلى إعطاء إرشادات حول طيرق تيدو نٌ الب اٌنيات التؽذو يٌة عليى البطاقية الب اٌن ةٌ للأؼذ ةٌ. تطبق هذه المواصفة الق اٌس ةٌ على جم عٌ الأؼذ ةٌ، إلا أنه مين الممكين وضيع اشيتراطات أكثير تفصي لًٌا للأؼذ ةٌ المعدة لاستعمالات تؽذو ةٌ خاصة. NL 719: 2017 ليبنور 8 جٌيب أن كٌيون ب يٌيان المؽيذ اٌت إلزام يٌيا لجم يٌيع الأؼذ يٌية المعبيأة مسيبقًا باسيتثناء الحيالات التي لا تيدعم الظروؾ الوطن ةٌ ف هٌيا هيذه الب اٌنيات. جٌوز اعفياء بعيض الأؼذ يٌة اليواردة في الملحيق ) 3( ميا ليم كٌين الالتزام على توف رٌ هذه المعلومات بموجب القواعد الوطن ةٌّ الأخرى. تجدر الاشارة الى أن ب اٌن المؽذ اٌت جٌب أن كٌون إلزام ا لكل الأؼذ ةٌ المعبأة مسب قا الت توضيع مين .) أجلها ادّعاءات ؼذائ ةٌ أوصح ةٌ حتّى لو وجدت ف الملحق ) 3

Paints and Varnishes — Terms and Definitions

Sector: PAINT AND COLOUR INDUSTRIES

Document Number: NL ISO 4619 : 2017

ISO 4618:2014 defines terms used in the field of coating materials (paints, varnishes and raw materials for paints and varnishes). Terms relating to specific applications and properties are dealt with in standards concerning those applications and properties, e.g. corrosion protection, coating powders. Terms and definitions from ISO 4618:2014 can be viewed free of charge on the ISO online browsing platform (OBP): https://www.iso.org/obp/ui/

Driers for Paints and Varnishes

Document Number: NL ISO 15528 : 2017

This document specifies the requirements and the corresponding test methods for driers for paints, varnishes and related products. It applies to driers in the solid or liquid form. It does not apply to emulsifiable driers.

Paints, Varnishes and Raw Materials for Paints and Varnishes — Sampling

Document Number: NL ISO 7507 1 : 2017

ISO 15528:2013 specifies procedures for the sampling of paints, varnishes and raw materials used in their manufacture. Such products include liquids and materials which, without undergoing chemical modification, are capable of being liquefied when heated up, and powdered, granulated and pasty materials. Samples may be taken from containers, e.g. cans, drums, tanks, tank wagons or ships' tanks, as well as from barrels, sacks, big-bags, silos or silo wagons, or from conveyor belts. ISO 15528:2013 does not deal with the sample preparation for testing or reduction of the samples thus taken. This is dealt with in ISO 1513.

Petroleum and Liquid Petroleum Products — Calibration of Vertical Cylindrical Tanks — Part 1: Strapping Method

Document Number: NL ISO 7507 2 : 2017

Applies to tanks with cylindrical courses that are substantially vertical. Provides a method suitable for use as a working method, a reference method or a referee method for measuring a tank using a steel strapping tape. The operation of strapping, the corrections to be made and the calculations leading to the compilation of the tank capacity table are described. For tilted tanks with a deviation of up to 3 % from the vertical a correction may be applied that is described.

Petroleum and Liquid Petroleum Products — Calibration of Vertical Cylindrical Tanks — Part 2: Optical Reference-Line Method

Document Number: NL ISO 7507 3 : 2017

Applies to tanks above 8 m in diameter with cylindrical courses that are substantially vertical. Provides a method for determining the volumetric quantity contained within a tank at gauged liquid levels using an optical plummet. The measurement required to determine the circumference may be made internally or externally. For tilted tanks with a deviation of up to 3 % from the vertical a correction as described in ISO 7507-1 may be applied.

Petroleum and Liquid Petroleum Products — Calibration of Vertical Cylindrical Tanks — Part 3: Optical-Triangulation Method

Document Number: NL ISO 7507 4 : 2017

Applies to tanks above 8 m in diameter with cylindrical courses that are substantially vertical. Provides a method for determining the volumetric quantity contained within a tank at gauged liquid levels by optical triangulation using theodolites and laser beams. The measurement required to determine the radius may be made internally or externally. The external method is applicable only to tanks that are free of insulation. For tilted tanks with a deviation of up to 3 % from the vertical a correction as described in ISO 7507-1 may be applied.

Petroleum and Liquid Petroleum Products — Calibration of Vertical Cylindrical Tanks — Part 4: Internal Electro-Optical Distance-Ranging Method

Document Number: NL ISO 7507 5 : 2017

ISO 7507-4:2010 specifies a method for the calibration of vertical cylindrical tanks having diameters greater than 5 m by means of internal measurements using an electro-optical distance-ranging (EODR) instrument, and for the subsequent compilation of tank capacity tables. ISO 7507-4:2010 is suitable for tanks tilted up to a 3 % deviation from the vertical, provided that a correction is applied for the measured tilt as described in ISO 7507-1:2003, Clause 11. ISO 7507-4:2010 also applies to tanks with floating roofs or internal floating blankets.

Petroleum and Liquid Petroleum Products — Calibration of Vertical Cylindrical Tanks — Part 5: External Electro-Optical Distance-Ranging Method